Base Standard Capabilities
Product features
Feature | Description |
---|---|
Processor (one of the following depending on model) |
|
Cache memory (one of the following depending on model) |
|
Chipset 1 |
|
Upgradeability | Upgradeable to two (2) processors |
On System Management Chipset | HP iLO (Firmware: HP iLO 4)2 |
Memory protection |
|
Memory 3 (one of the following depending on model) |
|
Network controller (one of the following depending on model) |
|
Expansion slots |
|
Maximum internal storage 8 |
|
Interfaces 9 |
|
Graphics | Integrated Matrox G200 video standard
HP iLO 4 On System Management Memory
|
Storage controller(one of the following depending on model) |
|
Industry standard compliance |
|
Security |
|
NOTE: 1. Click here for more information regarding Intel chipsets. 2. Click here for more information regarding HP ProLiant Gen8 and Management Solutions . 3. To realize the performance memory capabilities listed in this document, HP SmartMemory is required. Click here to see QuickSpecs for technical specifications and additional information . HP memory from previous generation servers are not fully compatible with Smart Memory features in Gen8 Servers. 4. Supports FCoE, Flex-10, TCP/IP offload engine, hardware-based accelerated iSCSI, iSCSI boot, and autosensing 10Gb/1Gb Ethernet. Each port is autosensing 1Gb/10Gb, and can interoperate with 1Gb HP BladeSystem c-Class interconnect components. Both ports will operate at the same speed. FlexFabric capabilities require the use of an HP Virtual Connect FlexFabric module. Fibre Channel over Ethernet (FCoE) is supported with the HP 10GbE Pass-Thru Module, HP 6120XG Blade Switch with the CEE license installed, HP Cisco B22HP Fabric Extender and HP Cisco B22HP Fabric Extender with 16 FET for BladeSystem c-Class. 5. FlexibleLOMs are not compatible with prior generation c-Class server blades. 6. This expansion slot supports dual-port mezzanine cards: one port is routed to interconnect module bay 3 and the other to bay 4. 7. This expansion slot supports dual-port and quad-port mezzanine cards. For dual-port cards, one port is routed to interconnect module bay 5 and the other to bay 6. For quad-port cards, one port is routed to interconnect module bay 5, one to bay 6, one to bay 7, and one to bay 8. A second processor must be installed (in processor slot 2) to have access to the second expansion slot (expansion slot 2). 8. The ProLiant BL420c Gen8 server includes the new HP hot plug small form factor (SFF) SmartDrive carrier for enhanced management and reduced maintenance errors. HP drives from previous generation servers are not compatible with the ProLiant BL420c Gen8 drive bays. 9. The above options are for integrated hypervisor virtualization environments needing a low cost boot solution with the highest performance and reliability. 10. Upgradeable firmware with recovery ROM. The HP Smart Array P220i supports two (2) small form factor (SFF) hot plug drive bays. 11. HP Dynamic Smart Array B320i supports two (2) small form factor (SFF) hot plug drive bays. The server supports up to a combined total of two (2) FBWC supercap options. |
Software overview
Feature | Description |
---|---|
Operating systems and Virtualization software support for ProLiant servers |
|
NOTE: For more information on HP's Certified and Supported ProLiant Servers for OS and Virtualization Software and latest listing of software drivers available for your server, please visit our Support Matrix and the driver download page. Click here to access the Support Matrix . Click here to access the driver download page . |
Physical specifications
Specification | Description |
---|---|
Dimensions (H x W x D) (with bezel) | 18.07 x 5.54 x 51.76 cm (7.11 x 2.18 x 20.37 in) |
Weight (approximate) | |
Maximum (all processors, 12 DIMMs, hard drives, mezzanine cards, and two flash cache batteries installed) | 6.33 kg (14.00 lb) |
Minimum (one processor and 2 DIMMs installed) | 4.75 kg (10.50 lb) |
Environmental specifications
Specification | Description |
---|---|
Operating temperature | 10° to 35°C (50° to 95°F) |
Non-operating temperature | -30° to 60°C (-22° to 140°F) |
Operating relative humidity | 10% to 90% non-condensing |
Non-operating relative humidity | 5% to 95% non-condensing |
Operating altitude | 3050 m (10,000 ft) |
Non-operating altitude | 9144 m (30,000 ft) |